Wulf Mods Flow Auto Flow 510 Voltage Battery｜ Other Products

Go With The Flow

Unleash your clouds like never before with the Wulf Mods Flow Auto Flow 510 Voltage Battery!
Use your Flow in traditional Auto Draw Mode or switch things up with Auto Flow Mode for a propulsive blast of silky vapor that is truly ferocious. This means when flip up the top on your Auto Flow, your Flow is going to turn into a mini fog machine - shooting out vapor like a flame thrower for a truly one of a kind way to experience your clouds. 
The Flow has some serious claws thanks to its 500mAh battery, choice of 5 temperature settings (1.8, 2.4, 2.8, 3.4. 3.8), ergonomic aluminum alloy body, and fiery 10s pre-heat mode. With a completely concealed cartridge chamber the Flow is as sleek as it is discreet, making it the ultimate on the go option. The Flow is available in a selection of 5 different colors including pack favorites like black-red spatter and purple-black spatter.

Loading A Cartridge Into The Flow
To begin vaping with your Flow, you must first head into your collection of 510 threaded cartridges and choose one to get started with! From there remove the bottom of your Flow and gently attach the cartridge via the 510 threaded connection port. Once on, carefully replace the bottom of your Flow and prepare for vapor fun!

Using Your Flow
To turn on your Flow Auto Flow 510 Voltage Battery press the power button located on the bottom of the device 5x in a row. When input successfully, your Flow will shine its LED to let you know that you are good to go. After your session concludes, turn off your Flow by repeating the process and pressing your power button 5x in a row.
Using Your Flow In Auto Draw Mode
To use your Flow in auto draw mode, simply make sure that the cap is flipped down and then inhale from the mouthpiece. As the Flow is auto draw activated, all you have to do is draw and it will instantly provide you with some clouds. When you're done, just stop inhaling and the Flow will go back to stand by mode until you hit it again.
Using Your Flow In Auto Flow Mode
To use your Flow in auto flow mode, all you have to do is flip the mouthpiece up to reveal the Flow’s nozzle and it will immediately begin emitting vapor for a flow of milky vapor. The Flow will flow vapor for 10s before stopping. To set up another round simply gently close the Flow’s mouthpiece and then open it up again to start the 10s vapor flow once more.
Adjusting The Flow’s Temperature
To switch between the 5 different temperature settings on the Flow, press the power button on the bottom of the device 1x, this will cycle the voltage to the next level in line. To make viewing your voltage easy, each of the 5 temperature settings has a corresponding LED color, yellow - 1.8v, purple 2.4v, green - 2.8v, blue - 3.4v, and red 3.8v. 

Pre-Heating Your Flow
Activate the Flow’s preheat mode by pressing the power button 2x in a row. When done correctly your Flow’s LED will come to life and start slowly cycling through the different colors to let you know your cartridge is being prepared. Once done, the LED’s will turn off and you will be ready to take a special pre heated blast from your Flow!
How To Charge The Flow
To charge your Flow make use of the USB-C port located on the bottom of the device. The first time you charge your Flow, make sure to leave it plugged in for 2 hours. Every single time after that first charge, never leave your Flow plugged in for longer than 1 hour at a time to avoid over charging and short circuiting. 

Troubleshooting Your Flow
To make using your Flow as smooth as possible, we recommend that you are aware of the following troubleshooting warnings that can pop up on your device. 

Over Time Warning: Your Flow will flash a red light 4x and switch to standby should you inhale from it longer than 10s at a time. 

Short Circuit Warning: Your Flow will flash a red light 3x to let you know it is experiencing a short circuity, cease to use your device until this warning stops. 

No Cart Warning: Your Flow will flash a white light 3 times if no cartridge is detected. 

Overload Warning: Your Flow will flash a white light 5x to indicate an overload warning.

How To Clean the Flow
Clean your Flow Auto Flow 510 Voltage Battery by first disassembling the bottom and cartridge components, before making use of a q-tip or swab lightly dampened with isopropyl alcohol to gently scrub any build up or grime that has accumulated. Make sure to leave ample time for your Flow to dry before attempting to use it again.

What’s Included: 

(1) Wulf Mods Flow Auto Flow 510 Voltage Battery 
Brand:General ShopTags:510 battery, Batteries, Discreet 510 Battery, wulf, wulf batteryColor:Black-Red Spatter, Black-White Spatter, Full Color, Purple-Black Spatter, Teal-Black Spatter